The Golden Gate Bridge is a suspension bridge spanning the Golden Gate, the opening of the San Francisco Bay into the Pacific Ocean. As part of both U.S. Route 101 and California State Route 1, the structure links the city of San Francisco, on the northern tip of the San Francisco Peninsula, to Marin County. It is one of the most internationally recognized symbols of San Francisco, California, and the United States. It has been declared one of the Wonders of the Modern World by the American Society of Civil Engineers.[7] The Frommers travel guide considers the Golden Gate Bridge "possibly the most beautiful, certainly the most photographed, bridge in the world".[8]Before the bridge was built, the only practical short route between San Francisco and what is now Marin County was by boat across a section of San Francisco Bay. Ferry service began as early as 1820, with regularly scheduled service beginning in the 1840s for purposes of transporting water to San Francisco.[9] The Sausalito Land and Ferry Company service, launched in 1867, eventually became the Golden Gate Ferry Company, a Southern Pacific Railroad subsidiary, the largest ferry operation in the world by the late 1920s.[9][10] Once for railroad passengers and customers only, Southern Pacific's automobile ferries became very profitable and important to the regional economy.[11] The ferry crossing between the Hyde Street Pier in San Francisco and Sausalito in Marin County took approximately 20 minutes and cost US$1.00 per vehicle, a price later reduced to compete with the new bridge.[12] The trip from the San Francisco Ferry Building took 27 minutes.
Many wanted to build a bridge to connect San Francisco to Marin County. San Francisco was the largest American city still served primarily by ferry boats. Because it did not have a permanent link with communities around the bay, the city's growth rate was below the national average.[13] Many experts said that a bridge couldn’t be built across the 6,700 ft (2,042 m) strait. It had strong, swirling tides and currents, with water 372 ft (113 m) deep[14] at the center of the channel, and frequent strong winds. Experts said that ferocious winds and blinding fogs would prevent construction and operation.[13]
The Millau Viaduct (French: le Viaduc de Millau, IPA: [vjadyk də mijo]) is a cable-stayed road-bridge that spans the valley of the river Tarn near Millau in southern France.
Designed by the French structural engineer Michel Virlogeux and British architect Norman Foster, it is the tallest bridge in the world with one mast's summit at 343.0 metres (1,125 ft) above the base of the structure.[3] [4] It is the 12th highest bridge deck in the world, being 270 metres (890 ft)[1] between the road deck and the ground below.[5] The viaduct is part of the A75-A71 autoroute axis from Paris to Montpellier. Construction cost was approximately €400 million. It was formally dedicated on 14 December 2004, inaugurated on the 15th, and opened to traffic on the 16th. The bridge received the 2006 IABSE Outstanding Structure Award.[6]Problems with traffic on the route from Paris to Spain along the stretch passing through the valley near the town of Millau, especially during the summer when the roads became jammed with holiday traffic, required construction of a bridge to span the valley.[7] The first plans were discussed in 1987 by CETE, and by October 1991, the decision was made to build a high crossing of the Tarn River by a structure of around 2,500 m (8,200 ft). During 1993–1994 the government consulted with seven architects and eight structural engineers. During 1995–1996, a second definition study was made by five associated architect groups and structural engineers. In January 1995, the government issued a declaration of public interest to solicit design approaches for a competition. [8]
In July 1996, the jury decided in favour of a cable-stayed design with multiple spans, as proposed by the Sogelerg consortium (Michel Virlogeux and Norman Foster). The decision to proceed by grant of contract was made in May 1998; then in June 2000 the contest for the construction contract was launched, open to four consortia. In March 2001 Eiffage established the subsidiary Compagnie Eiffage du Viaduc de Millau (CEVM) and was declared winner of the contest and awarded the prime contract in August.
Designed by the French structural engineer Michel Virlogeux and British architect Norman Foster, it is the tallest bridge in the world with one mast's summit at 343.0 metres (1,125 ft) above the base of the structure.[3] [4] It is the 12th highest bridge deck in the world, being 270 metres (890 ft)[1] between the road deck and the ground below.[5] The viaduct is part of the A75-A71 autoroute axis from Paris to Montpellier. Construction cost was approximately €400 million. It was formally dedicated on 14 December 2004, inaugurated on the 15th, and opened to traffic on the 16th. The bridge received the 2006 IABSE Outstanding Structure Award.[6]Problems with traffic on the route from Paris to Spain along the stretch passing through the valley near the town of Millau, especially during the summer when the roads became jammed with holiday traffic, required construction of a bridge to span the valley.[7] The first plans were discussed in 1987 by CETE, and by October 1991, the decision was made to build a high crossing of the Tarn River by a structure of around 2,500 m (8,200 ft). During 1993–1994 the government consulted with seven architects and eight structural engineers. During 1995–1996, a second definition study was made by five associated architect groups and structural engineers. In January 1995, the government issued a declaration of public interest to solicit design approaches for a competition. [8]
In July 1996, the jury decided in favour of a cable-stayed design with multiple spans, as proposed by the Sogelerg consortium (Michel Virlogeux and Norman Foster). The decision to proceed by grant of contract was made in May 1998; then in June 2000 the contest for the construction contract was launched, open to four consortia. In March 2001 Eiffage established the subsidiary Compagnie Eiffage du Viaduc de Millau (CEVM) and was declared winner of the contest and awarded the prime contract in August.
The Forth Bridge is a cantilever railway bridge over the Firth of Forth in the east of Scotland, to the east of the Forth Road Bridge, and 14 kilometres (9 mi) west of central Edinburgh. It was opened on 4 March 1890, and spans a total length of 2,528.7 metres (8,296 ft). It is often called the Forth Rail Bridge or Forth Railway Bridge to distinguish it from the Forth Road Bridge, although it has been called the "Forth Bridge" since its construction, and was for over seventy years the sole claimant to this name.
The bridge connects Scotland's capital city, Edinburgh, with Fife, leaving the Lothians at Dalmeny and arriving in Fife at North Queensferry; it acts as a major artery connecting the north-east and south-east of the country. Described by the Collins Encyclopaedia of Scotland as "the one immediately and internationally recognised Scottish landmark",[1] it is a Category A listed building[2][3] and was nominated by the British government in May 2011 for addition to the UNESCO World Heritage Sites in Scotland.[4]
Until 1917, when the Quebec Bridge was completed, the Forth Bridge had the longest single cantilever bridge span in the world. It still has the world's second-longest single span.[5][6] The bridge and its associated railway infrastructure is owned by Network Rail Infrastructure Limited.Construction of an earlier bridge, a suspension bridge designed by Sir Thomas Bouch, got as far as the laying of the foundation stone, but was stopped after the collapse of another of his works, the Tay Bridge. The public inquiry into the Tay bridge disaster declared the Tay Bridge "poorly designed, poorly constructed and poorly maintained".[7] Bouch was disgraced, and the project was subsequently taken over by Sir John Fowler and Sir Benjamin Baker, who designed a structure that was built by Glasgow based company Sir William Arrol & Co. between 1883 and 1890. Baker and his colleague Allan Stewart received the major credit for design and overseeing building work.The bridge was the first major structure in Britain to be constructed of steel;[8] its contemporary, the Eiffel Tower was built of wrought iron.
Large amounts of steel had become available only after the invention of the Bessemer process in 1855. Until 1877 the British Board of Trade had limited the use of steel in structural engineering because the process produced steel of unpredictable strength. Only the Siemens-Martin open-hearth process developed by 1875 yielded steel of consistent quality. The 64,800 tons[clarification needed] of steel needed for the bridge was provided by two steel works in Scotland and one in Wales.[9]
The Octavio Frias de Oliveira bridge is a cable-stayed bridge in São Paulo, Brazil over the Pinheiros River, opened in May 2008. The bridge is 138 metres (453 ft) tall, and connects Marginal Pinheiros to Jornalista Roberto Marinho Avenue in the south area of the city.The bridge connects Scotland's capital city, Edinburgh, with Fife, leaving the Lothians at Dalmeny and arriving in Fife at North Queensferry; it acts as a major artery connecting the north-east and south-east of the country. Described by the Collins Encyclopaedia of Scotland as "the one immediately and internationally recognised Scottish landmark",[1] it is a Category A listed building[2][3] and was nominated by the British government in May 2011 for addition to the UNESCO World Heritage Sites in Scotland.[4]
Until 1917, when the Quebec Bridge was completed, the Forth Bridge had the longest single cantilever bridge span in the world. It still has the world's second-longest single span.[5][6] The bridge and its associated railway infrastructure is owned by Network Rail Infrastructure Limited.Construction of an earlier bridge, a suspension bridge designed by Sir Thomas Bouch, got as far as the laying of the foundation stone, but was stopped after the collapse of another of his works, the Tay Bridge. The public inquiry into the Tay bridge disaster declared the Tay Bridge "poorly designed, poorly constructed and poorly maintained".[7] Bouch was disgraced, and the project was subsequently taken over by Sir John Fowler and Sir Benjamin Baker, who designed a structure that was built by Glasgow based company Sir William Arrol & Co. between 1883 and 1890. Baker and his colleague Allan Stewart received the major credit for design and overseeing building work.The bridge was the first major structure in Britain to be constructed of steel;[8] its contemporary, the Eiffel Tower was built of wrought iron.
Large amounts of steel had become available only after the invention of the Bessemer process in 1855. Until 1877 the British Board of Trade had limited the use of steel in structural engineering because the process produced steel of unpredictable strength. Only the Siemens-Martin open-hearth process developed by 1875 yielded steel of consistent quality. The 64,800 tons[clarification needed] of steel needed for the bridge was provided by two steel works in Scotland and one in Wales.[9]
The bridge deck is unusual due to its form, which is similar to an "X", crossing at the tower. The "X" is 76 meters wide at its base and 35.4 meters wide at the top.
It is the only bridge in the world that has two curved tracks supported by a single concrete mast. The two curved tracks, one at an elevation of 12 meters and the other at an elevation of 24 meters, have approximate lengths of 900 meters each.
At the end of December lights are put up on the cables and illuminated to create color effects like those on a Christmas tree. The bridge is also lit up on special occasions during the year and is often used for automobile advertisements on television.
The bridge has been attacked by vandals on several occasions. In 2011, thieves stole 6 kilometres (3.7 mi) of wire, worth R$ 200,000.00 (US$ 117,000.00).[2] Later in August, vandals broke in the bridge's control room and destroyed the panels.[2] On January 9, 2012, vandals stole 94 of the 142 searchlights of the bridge.[2] It will take 90 days and R$ 1,000,000.00 (US$ 590,000.00) to completely re-establish the lighting system.[2]
Tower Bridge (built 1886–1894) is a combined bascule and suspension bridge in London, over the River Thames. It is close to the Tower of London, from which it takes its name.[1] It has become an iconic symbol of London.
The bridge consists of two towers tied together at the upper level by means of two horizontal walkways, designed to withstand the horizontal forces exerted by the suspended sections of the bridge on the landward sides of the towers. The vertical component of the forces in the suspended sections and the vertical reactions of the two walkways are carried by the two robust towers. The bascule pivots and operating machinery are housed in the base of each tower. The bridge's present colour scheme dates from 1977, when it was painted red, white and blue for the Queen Elizabeth II's silver jubilee. Originally it was painted a mid greenish-blue colour.[2]Tower Bridge is sometimes mistakenly referred to as London Bridge,[3] which is the next bridge upstream.
The nearest London Underground station is Tower Hill on the Circle and District lines, and the nearest Docklands Light Railway station is Tower Gateway.[4]In the second half of the 19th century, increased commercial development in the East End of London led to a requirement for a new river crossing downstream of London Bridge. A traditional fixed bridge could not be built because it would cut off access by tall-masted ships to the port facilities in the Pool of London, between London Bridge and the Tower of London.
A Special Bridge or Subway Committee was formed in 1876, chaired by Sir Albert Joseph Altman, to find a solution to the river crossing problem. It opened the design of the crossing to public competition. Over 50 designs were submitted, including one from civil engineer Sir Joseph Bazalgette. The evaluation of the designs was surrounded by controversy, and it was not until 1884 that a design submitted by Sir Horace Jones, the City Architect (who was also one of the judges),[5] was approved.
Jones' engineer, Sir John Wolfe Barry, devised the idea of a bascule bridge with two towers built on piers. The central span was split into two equal bascules or leaves, which could be raised to allow river traffic to pass. The two side-spans were suspension bridges, with the suspension rods anchored both at the abutments and through rods contained within the bridge's upper walkways.Construction started in 1886 and took eight years with five major contractors – Sir John Jackson (foundations), Baron Armstrong (hydraulics), William Webster, Sir H.H. Bartlett, and Sir William Arrol & Co.[6] – and employed 432 construction workers. E W Crutwell was the resident engineer for the construction.[7]
Two massive piers, containing over 70,000 tons of concrete,[5] were sunk into the riverbed to support the construction. Over 11,000 tons of steel provided the framework for the towers and walkways.[5] This was then clad in Cornish granite and Portland stone, both to protect the underlying steelwork and to give the bridge a pleasing appearance.
Jones died in 1887 and George D. Stevenson took over the project.[5] Stevenson replaced Jones's original brick façade with the more ornate Victorian Gothic style, which makes the bridge a distinctive landmark, and was intended to harmonise the bridge with the nearby Tower of London.[7] The total cost of construction was £1,184,000[7] (£100 million as of 2012).[8]
The Sydney Harbour Bridge is a steel through arch bridge across Sydney Harbour that carries rail, vehicular, bicycle and pedestrian traffic between the Sydney central business district (CBD) and the North Shore. The dramatic view of the bridge, the harbour, and the nearby Sydney Opera House is an iconic image of Sydney, New South Wales, and Australia. The bridge is nicknamed "The Coathanger" because of its arch-based design.[1][2]
Under the directions of Dr J.J.C. Bradfield of the NSW Department of Public Works, the bridge was designed and built by British firm Dorman Long and Co Ltd of Middlesbrough and opened in 1932.[3][4] The bridge's design was influenced by the Hell Gate Bridge in New York.[5] It was the world's widest long-span bridge until construction of the new Port Mann Bridge in Vancouver.[6][7] It is also the fifth longest spanning-arch bridge in the world, and it is the tallest steel arch bridge, measuring 134 metres (440 ft) from top to water level.[8] Until 1967 the Harbour Bridge was Sydney's tallest structure.[citation needed]The southern (CBD) bridge end is located at Millers Point in The Rocks area, and the northern end at Milsons Point in the lower North Shore area. It carries six lanes of road traffic on its main roadway, while on its eastern side are two lanes of road traffic (formerly two tram tracks) and a footpath, and on its western side are two railway tracks and a bicycle path, making the western side 30.5 cm (12 in) broader than the eastern side.
The main roadway across the bridge is known as the Bradfield Highway and is about 2.4 kilometres (1.5 mi) long, making it one of the shortest highways in Australia. (The shortest, also called the Bradfield Highway, is found on the Story Bridge in Brisbane.)The arch is composed of two 28-panel arch trusses; their heights vary from 18 m (59 ft) at the centre of the arch to 57 m (187 ft) at the ends next to the pylons.
The arch has a span of 503 m and its summit is 134 m (440 ft) above mean sea level; however, expansion of the steel structure on hot days can increase the height of the arch by as much as 18 cm (7.1 in).[9] Large steel pins support each end of the arch, allowing it to rotate to accommodate expansion and contraction caused by changes of temperature, and avoiding stresses that would otherwise cause damage.
The total weight of the steelwork of the bridge, including the arch and approach spans, is 52,800 tonnes, with the arch itself weighing 39,000 tonnes.[10] About 79% of the steel was imported from England, with the rest being sourced from Australia.[11] On site, the contractors set up two workshops at Milsons Point, at the site of the present day Luna Park, and fabricated the steel into the girders and other required parts.[11]
The bridge is held together by six million Australian-made hand-driven rivets supplied by the McPherson company of Melbourne,[12][13] the last being driven through the deck on 21 January 1932.[11][14] The rivets were heated red-hot and inserted into the plates; the headless end was immediately rounded over with a large pneumatic rivet gun.[15] The largest of the rivets used weighed 3.5 kg (8 lb) and was 39.5 cm (15.6 in) long.[10][16] The practice of riveting large steel structures, rather than welding, was, at the time, a proven and understood construction technique, whilst structural welding had not at that stage been adequately developed for use on the bridge.[15]There had been plans to build a bridge as early as 1815, when convict and noted architect Francis Greenway reputedly proposed to Governor Lachlan Macquarie that a bridge be built from the northern to the southern shore of the harbour.[8][23] In 1825 Greenway wrote a letter to the then "The Australian" newspaper stating that such a bridge would "give an idea of strength and magnificence that would reflect credit and glory on the colony and the Mother Country".[23]Nothing came of Greenway's suggestions, but the idea remained alive, and many further suggestions were made during the nineteenth century. In 1840, naval architect Robert Brindley proposed that a floating bridge be built. Engineer Peter Henderson produced one of the earliest known drawings of a bridge across the harbour around 1857. A suggestion for a truss bridge was made in 1879, and in 1880 a high-level bridge estimated at $850,000 was proposed.[23] In 1900 the Lyne government committed to building a new Central railway station and organised a worldwide competition for the design and construction of a harbour bridge. Local engineer Norman Selfe submitted a design for a suspension bridge and won the second prize of £500. In 1902, when the outcome of the first competition became mired in controversy, Selfe won a second competition outright, with a design for a steel cantilever bridge. The selection board were unanimous, commenting that, "The structural lines are correct and in true proportion, and... the outline is graceful".[24] However due to an economic downturn and a change of government at the 1904 NSW State election construction never began.In 1912 J.J.C. Bradfield was appointed "Chief Engineer of Sydney Harbour Bridge and Metropolitan Railway Construction", and his work on the project over many years earned him the legacy as the "father" of the bridge.[3] Bradfield's preference at the time was for a cantilever bridge without piers, and in 1916 the NSW Legislative Assembly passed a bill for such a construction, however it did not proceed as the Legislative Council rejected the legislation on the basis that the money would be better spent on the war effort.[23]
Following World War I, plans to build the bridge again built momentum.[8] Bradfield persevered with the project, fleshing out the details of the specifications and financing for his cantilever bridge proposal, and in 1921 he travelled overseas to investigate tenders. On return from his travels Bradfield decided that an arch design would also be suitable[23] and he and officers of the NSW Department of Public Works prepared a general design[3][8] for a single-arch bridge based upon New York City's Hell Gate Bridge.[5][25] In 1922 the government passed the Sydney Harbour Bridge Act No. 28, specifying the construction of a high-level cantilever or arch bridge across the harbour between Dawes Point and Milsons Point, along with construction of necessary approaches and electric railway lines,[23] and worldwide tenders were invited for the project.[3]
As a result of the tendering process, the government received twenty proposals from six companies; on 24 March 1924 the contract was awarded to English firm Dorman Long and Co Ltd, of Middlesbrough well known as the contractors who built the similar Tyne Bridge of Newcastle Upon Tyne, for an arch bridge at a quoted price of AU£4,217,721 11s 10d.[3][23] The arch design was cheaper than alternative cantilever and suspension bridge proposals, and also provided greater rigidity making it better suited for the heavy loads expected.[23]
To offset concerns about a foreign firm participating in the project, assurances were given by Bradfield that the workforce building the bridge would all be Australians.[citation needed] Bradfield and his staff were ultimately to oversee the entire bridge design and building process, while Dorman Long and Co's Consulting Engineer, Sir Ralph Freeman of Sir Douglas Fox and Partners, and his associate Mr. G.C. Imbault, carried out the detailed design and erection process of the bridge.[3] Architects for the contractors were from the British firm John Burnet & Partners of Glasgow, Scotland.[20]
The building of the bridge coincided with the construction of a system of underground railways in Sydney's CBD, known today as the City Circle, and the bridge was designed with this in mind. The bridge was designed to carry six lanes of road traffic, flanked on each side by two railway tracks and a footpath. Both sets of rail tracks were linked into the underground Wynyard railway station on the south (city) side of the bridge by symmetrical ramps and tunnels. The eastern-side railway tracks were intended for use by a planned rail link to the Northern Beaches;[citation needed] in the interim they were used to carry trams from the North Shore into a terminal within Wynyard station, and when tram services were discontinued in 1958, they were converted into extra traffic lanes. The Bradfield Highway, which is the main roadway section of the bridge and its approaches, is named in honour of Bradfield's contribution to the bridge.
Navajo Bridge crosses the Colorado River's Marble Canyon near Lee's Ferry in the US state of Arizona. Apart from the Glen Canyon Bridge a few miles upstream at Page, Arizona, it is the only roadway crossing of the river and the Grand Canyon for nearly 600 miles (970 km). Spanning Marble Canyon, the bridge carries northbound travelers to southern Utah and to the Arizona Strip, the otherwise inaccessible portion of Arizona north of the Colorado River, which includes the North Rim of Grand Canyon National Park.
Prior to the construction of the first Navajo Bridge, the only river crossing from Arizona to Utah was at nearby Lee's Ferry, where the canyon walls are low and getting vehicles onto the water is relatively convenient. The ferry offered only unreliable service, however, as adverse weather and flooding regularly prevented its operation.Construction of the original Navajo Bridge began in 1927, and the bridge opened to traffic in 1929. It was paid for by the nascent Arizona State Highway Commission (now the Arizona Department of Transportation) in cooperation with the United States Department of the Interior's Bureau of Indian Affairs, as the eastern landing is on the Navajo Nation. The steel spandrel bridge design was constructed by the Kansas City Structural Steel Company. The bridge is 834 feet (254 m) in length, with a maximum height of 467 feet (142 m) from the canyon floor. Its roadway offers an 18-foot (5.5 m) surface width with a load capacity of 22.5 tons (although the posted legal weight limit was 40 tons). During the design phase, a wider roadway was considered, but ultimately rejected, as it would have required a costly third arch to be added to the design, and the vehicles of the time did not necessitate the wider road.
In 1990, however, it was decided that the traffic flow was too great for the original bridge, and that a new solution was needed. The sharp corners in the roadway on each side of the bridge's approach had become a safety hazard due to low visibility, and the deficiency in the original design's width and load capacity specifications were becoming problematic. The bridge had also become part of U.S. Route 89A.Deciding on a solution was difficult, due to the many local interests. Issues included preservation of sacred Navajo land, endangered plant species in Marble Canyon, and the possibility of construction pollution entering the river. The original proposal called for merely widening and fortifying the bridge, but this was ultimately rejected since this could not possibly bring it up to current federal highway standards. Replacement was then the only option, and it was eventually decided to entirely discontinue automobile use of the original bridge. A new bridge would be built immediately next to the original and have a considerably similar visual appearance, but would conform to modern highway codes.
The new steel arch bridge was commissioned by the Arizona Department of Transportation and the Federal Highway Administration, and was completed in September 1995, at a cost of approximately $15 million.
The original Navajo Bridge is still open to pedestrian and equestrian use, and an interpretive center has been constructed nearby to showcase the historical nature of the bridge and early crossing of the Colorado River. Bungee jumpers are frequently seen using the span. The original bridge has been designated as a Historic Civil Engineering Landmark. The bridge was placed on the National Register of Historic Places on August 13, 1981.[3]
The Seven Mile Bridge is a famous bridge in the Florida Keys, in Monroe County, Florida, United States. It connects Knight's Key (part of the city of Marathon, Florida) in the Middle Keys to Little Duck Key in the Lower Keys. Among the longest bridges in existence when it was built, it is one of the many bridges on US 1 in the Keys, where the road is called the Overseas Highway.
There are two bridges in this location. The older bridge, originally known as the Knights Key-Pigeon Key-Moser Channel-Pacet Channel Bridge, was constructed from 1909-1912 under the direction of Henry Flagler as part of the Florida East Coast Railway's Key West Extension, also known as the Overseas Railroad.After the railroad sustained considerable damage due to effects of the Labor Day Hurricane of 1935, the line was sold to the United States Federal Government, who subsequently refurbished Seven Mile Bridge for automobile use. Dismantled trackage was recycled, painted white, and used as guardrails. It had a swing span that opened to allow passage of boat traffic, near where the bridge crosses Pigeon Key, a small island where a work camp for Flagler's railroad was located. Hurricane Donna in 1960 caused further damage.
The current road bridge was constructed from 1978 to 1982. The vast majority of the original bridge still exists, used as fishing piers and access to Pigeon Key, but the swing span over the Moser Channel of the Intracoastal Waterway has been removed.The new bridge is a box-girder structure built from precast, prestressed concrete sections, comprising 440 spans. Near the center, the bridge rises in an arc to provide 65-foot (20 m)-high clearance for boat passage. The remainder of the bridge is considerably closer to the water surface. The new bridge does not cross Pigeon Key.
The total length of the new bridge is actually 35,862 ft (10,931 m) or 6.79 miles (10.93 km), and is shorter than the original. Each April the bridge is closed for approximately 2.5 hours on a Saturday and a "fun run," known as the Seven Mile Bridge Run, of 1,500 runners is held commemorating the Florida Keys bridge rebuilding project. The event began in 1982 to commemorate the completion of a federally funded bridge building program that replaced spans that oil tycoon Henry Flagler constructed in the early 1900s to serve as a foundation for his Overseas Railroad.
The Seven Mile Bridge was engineered by Figg & Muller Engineers. The structure was completed six months ahead of schedule and has earned eight awards, including an Exceptional Award for Cost Savings Innovation from the Federal Highway Administration.
The San Diego–Coronado Bridge, locally referred to as the Coronado Bridge, is a "prestressed concrete/steel" girder bridge, crossing over San Diego Bay in the United States, linking San Diego with Coronado, California.[1] The bridge is signed as part of State Route 75.The 11,179-foot-long (3,407 m or 2.1 mi) bridge ascends from Coronado at a 4.67 percent grade before curving 80 degrees toward San Diego. The span reaches a maximum height of 200 feet (61m), allowing the U.S. Navy ships which operate out of the nearby Naval Station San Diego to pass underneath it. The five-lane bridge featured the longest box girder in the world until it was surpassed by a bridge in Chongqing, China in 2008.[2] The bridge does not form a direct path to Coronado, but rather has a curve. This was done so it would be high enough for all U.S. Navy ships to pass underneath but not too steep for vehicles to ascend and descend.
Construction on the San Diego–Coronado Bay Bridge started in February 1967, and opened to traffic on August 3, 1969, during the celebration of the 200th anniversary of the founding of San Diego[3]The bridge contains five lanes: two eastbound, two westbound, and a reversible middle lane with a moveable barrier system which can be used to create a third lane in either direction in response to traffic volume.[3] The eastern end of the bridge connects directly to a T interchange with Interstate 5, just southeast of downtown San Diego. It is designated and signed as part of California State Highway 75. The bridge was designed entirely and exclusively for motor vehicle traffic; there are no pedestrian walkways, bike paths, or shoulders ("breakdown lanes"). Beginning in 2008, cyclists have the once-a-year opportunity to ride over the bridge in the Bike the Bay "fun ride".[7]
The Verrazano-Narrows Bridge is a double-decked suspension bridge that connects the boroughs of Staten Island and Brooklyn in New York City at the Narrows, the reach connecting the relatively protected upper bay with the larger lower bay.
The bridge is named for both the Italian explorer Giovanni da Verrazzano, the first known European navigator in the service of the French crown to enter New York Harbor and the Hudson River, and for the body of water it spans: the Narrows. It has a center span of 4,260 feet (1,298 m) and was the longest suspension bridge in the world at the time of its completion in 1964, until it was surpassed by the Humber Bridge in the United Kingdom in 1981. It now has the ninth longest main span in the world, is still the longest bridge span in the Americas, and its massive towers can be seen throughout a good part of the New York metropolitan area, including from spots in all five boroughs of New York City and in New Jersey.
The bridge furnishes a critical link in the local and regional highway system. Since 1976, it has been the starting point of the New York City Marathon.[4] The bridge marks the gateway to New York Harbor; all cruise ships and most container ships arriving at the Port of New York and New Jersey must pass underneath the bridge and thus must be built to accommodate the clearance under the bridge. This is most notable in the case of the ocean liner RMS Queen Mary 2.The bridge is owned by the City of New York and operated by MTA Bridges and Tunnels, an affiliate agency of the Metropolitan Transportation Authority. Interstate 278 passes over the bridge, connecting the Staten Island Expressway with the Gowanus Expressway and the Belt Parkway. The Verrazano, along with the other three major Staten Island bridges, created a new way for commuters and travelers to reach Brooklyn, Long Island, and Manhattan by car from New Jersey.
The bridge was the last great public works project in New York City overseen by Robert Moses, the New York State Parks Commissioner and head of the Triborough Bridge and Tunnel Authority, who had long desired the bridge as a means of completing the expressway system which was itself largely the result of his efforts. The bridge was also the last project designed by Chief Engineer Othmar Ammann, who had also designed most of the other major crossings of New York City, including the George Washington Bridge, the Bayonne Bridge, the Bronx Whitestone Bridge, the Triborough Bridge, and the Throgs Neck Bridge. The plans to build the bridge caused considerable controversy in the Brooklyn neighborhood of Bay Ridge, because many families had settled in homes in the area where the bridge now stands and were forced to relocate.Construction on the bridge began August 13, 1959, and the upper deck was opened on November 21, 1964, at a cost of $320 million.[5][6] Three men died building the bridge, including nineteen-year-old Gerard McKee, whose death became the subject of a chapter of Gay Talese's book, The Bridge.[7][8]
New York City Mayor Robert F. Wagner cut the ribbon at the opening ceremony, which was attended by over 5,000 people. He was the first person to be driven over the bridge.[9] The lower deck opened on June 28, 1969.[10] The bridge took over the title of the longest suspension bridge in the world (previously held by the Golden Gate Bridge) from 1964 until 1981, when it was eclipsed by the Humber Bridge in England.
Fort Lafayette was an island coastal fortification in New York Harbor, built next to Fort Hamilton at the southern tip of what is now Bay Ridge. It was destroyed as part of the bridge's construction in 1960; the Brooklyn-side bridge pillars now occupy the fort's former foundation.
According to the U.S. Department of Transportation:
Each of the two towers contains 1 million bolts and 3 million rivets.
The diameter of each of the four suspension cables is 36 inches (914 mm). Each cable is composed of 26,108 wires amounting to a total of 143,000 miles (230,136 km) in length
Because of the height of the towers (693 ft/211 m) and their distance apart (4,260 ft/1,298 m), the curvature of the Earth's surface had to be taken into account when designing the bridge—the towers are 15⁄8 inches (41.275 mm) farther apart at their tops than at their bases.[11]
Because of thermal expansion of the steel cables, the bridge roadway is 12 feet (3.66 m) lower in summer than in winter.[12]The bridge is affected by weather more than any other bridge in the city because of its size and isolated location close to the open ocean. It is occasionally closed (either partially or entirely) during strong wind and snow storms.
the RMS Queen Mary 2 was designed with a flatter funnel to pass under the bridge, and has 13 feet (3.96 m) of clearance under the bridge during high tide.[13]
The bridge has fostered more traffic on the Outerbridge Crossing and the Goethals Bridge, both of which connect Staten Island with New Jersey.
In 2009 all 262 of the mercury vapor fixtures in the bridge's necklace lighting were replaced with energy efficient light-emitting diodes.[14]





















No comments:
Post a Comment